Colorlight VX10 Video Processor 4K LED Screen Controller for Rental Stage LED Display
Features
Input
- Video input port
-1×HDMI2.0
-1×HDMI1.4 (IN&LO0P)
-1×DVI (IN&L00P)
-1×DVI
-1×3G-SDI (IN&LO0P)
-1×10G fiber port (Fiber1)
- Up to 4096x2160@60Hz input.
- Support 8bit/10bit video signal.
- The HDMI2.0 port supports HDCP2.2 standard and is compatible with HDCP1.4 standard.
- The HDMI1.4 and DVI ports support HDCP1.4 standard.
- 23.98Hz to 240Hz frame rate
Output
- 10×Gigabit network ports.
-Maximum loading capacity of 6.5 million pixels,with up to 16,384 pixels in width
and 8,192 pixels in height.
- 2×10 Gigabit fiber ports.
-Fiber1 copies 10×Ethernet ports.
-Fiber2 copies/backups 10×Ethernet ports.
- Fiber port supports Video loop output
-Support up to 1×4K×1K@60Hzor 2×2K×1K@60Hz video source.
- 1×HDMI1.3 as previewing or video output port.
- 23.98Hz to 240Hz frame rate.
- Support both Ethernet port backup and controller redundancy.
Video Processing
- Support 8bit and 10bit video processing.
- Video signal cropping,switching,and broadcasting-level scaling.
- Support 3×layers display,as well as independent adjustment of size and position of layers.
- No latency achievable in Bypass mode.
- Support HDR display.
- Support Genlock and LOOP through.
Color adjustment
- Image adjustment Support adjusting the hue,saturation,contrast,and brightness compensation of output.
- Brightness adjustment:Support adjusting brightness by Ethernet port groups.
- Color temperature adjustment:Support adjusting color temperature accurately and RGB component individually.
Audio input/output
- HDMI port supports audio input.
- Support audio output via multi-function card.
3 working modes
- Video processor
- Fiber optic transceiver
- Bypass
Device control
- USB port for control and cascading.
- RS232 serial communication protocol.
- LAN port for TCP/IP control.
Appearance
Front Panel
|
No. |
ltem |
Description |
|
1 |
LCD |
Display operation menu and system information. |
|
2 |
Knob |
·Press to enter sub-menu or confirm selection.·Rotate to select menu item or tune parameters. |
|
3 |
ESC |
Exit current interface |
|
4 |
Function buttons |
·Main/PIP1/PIP2:Open/Close the layer and display layerstatus.
·Full Screen:Enable full screen auto-scaling. ·HDMI1/HDMI2/DVI1/DVI2/SDI/Fiber 1-1/Fiber 1-2/ Mosaic:Switch to corresponding signal. ·Preset:Select a preset. ·Bright:Tune brightness. ·Freeze:Freeze the current frame of the output image ·FN:A customizable function button. |
|
5 |
Power Switch |
Power on/off the device. |
*The illustration is for reference only.Since the appearance of equipment may vary due to different production process,please refer to the actual product.
Rear Panel
| Control | ||
| 1 | LAN | ·RJ45 port for accessing local area network. |
| 2 | RS232 | ·RJ11(6P6C)port*for connecting to central control. |
| 3 | USB IN | ·USB2.0 Type B port;Support cascading input and connectionwith PC for parameter configuration. |
| USB OUT | ·USB2.0 Type A port for cascading output. | |
| 3D port | ||
| 4 | 3D* |
Output 3D sync signal (Optional,work with active 3D glasses). |
| Genlock | ||
|
5 |
GENLOCK | ·1×BNC port,male,for the input of an external synchronizationsource.·Support Bi-level and Tri-level sync·Support 23.98~60Hz frame rates. |
| GENLOCKLOOP | ·1×BNC port,male.·Loop out Genlock sync signal. | |
| Input | ||
|
6 |
3G SDI
SDI LOOP |
·1×SDI input,support Loop output.·Support ST-424(3G),ST-292(HD),and ST-259(SD)standard videosource input.·Maximum resolution:1920×1080@60Hz
·Support de-interlaced display. ·Not support EDID settings. |
| 7 | HDMI1(2.0) | ·1×HDMI2.0 input,backward compatible with HDMI1.4 andHDMI1.3.·Maximum resolution:4096×2160@60Hz,minimum resolution:800×600@60Hz,maximum pixel clock:600MHz
·Custom resolution: |
| -Maximum width:8192(8192×1080@60Hz).-Maximum height:8192(1080×8192@60Hz).·Support independent EDID settings.·Support HDCP2.2 standard and compatible with HDCP1.4
standard. ·Support HDR ·Support audio input. ·Not support interlaced signal inputs. |
||
|
8 |
HDMI 2(1.4) HDMI 2 LOOP |
·1×HDMI1.4 input,HDMI2 support LO0P output.·Maximum resolution:4096×1080@60Hz/4096×2160@30Hz, minimum input resolution:800×600@60Hz.·Custom resolution:-Maximum width:4096 (4096×1080@60Hz).
-Maximum height:4096 (1080×4096@60Hz). Support independent EDID settings. ·Support HDCP1.4 ·Support audio input. ·Not support HDR. ·Not support interlaced signal inputs. |
|
9 |
DVI 1 DVI 2 DVI 2 LOOP |
·2×DVl input;DVI2 support Loop output·Maximum resolution:4096×1080@60Hz/4096×2160@30Hz,minimum resolution:800×600@60Hz.·Custom resolution:
-Maximum width:4096 (4096×1080@60Hz). -Maximum height:4096 (1080×4096@60Hz). ·Support HDCP1.4. ·Support independent EDID settings. ·Not support audio input. ·Not support HDR. ·Not support interlaced signal input. |
| 10 | U-DISK | ·USB drive port;support receiver card parameter configuration. |
| Output | ||
|
11 |
PORT 1-10 |
10×1G Ethernet ports.·Overall loading capacity,6.5 million pixels:-Up to 16,384 pixels in width and 8,192 pixels in height.-8bit@60Hz:6.5 million pixels;10bit@60Hz:4.9 million pixels.
-8bit@120Hz:3.25 million pixels;10bit@120Hz:2.45 million pixels. -8bit@240Hz:1.62 million pixels;10bit@240Hz:1.22 million pixels. ·Loading capacity per port,650,000 pixels; -8bit@60Hz:650,000 pixels;10bit@60Hz:490,000 pixels. -8bit@120Hz:320,000 pixels;10bit@120Hz:240,000 pixels. -8bit@240Hz:160,000 pixels;10bit@240Hz:120,000 pixels. ·Communication distance:The recommended maximum cable (CAT5e)run length is 100 meters. ·Support redundancy. |
|
12 |
Fiber 1-2 |
·2×10G fiber ports (optional 10G SFP+optical module.
Transmission distance depends on optical module specifications). ·Fiber1:Fiber port self-adaptive,either for input or output. -When fiber optic transceiver is the device to be connected,the fiber port works as an output port -When 10×Ethernet ports and Fiber l are all connected,the 10 ×Ethernet ports work normally while the Fiber1 dose not work -When Fiber1 is not connected while the 10×Ethernet ports are connected,the 10×Ethernet ports work normally. -When fiber port of the vide processor is the device to be connected,the fiber port works asan input port. -Fiber l supports up to 1×4K×1K@60Hz or2×2K×1K@60Hz video source inputs. ·Fiber2: For output only. -1~10 Ethernet ports:Transmit data from up to 10×Ethernet ports in copy or backup mode). -Video loop output:Support up to 1×4K×1K@60Hz or2×2K× 1K@60Hz video source. -Optional loop output video source:SDI,HDMI1(2.0),HDMI2,DVI1 DVI2,Fiber1-1,Fiber1-2. |
| 13 | HDMI OUT | ·1×HDMI1.3 port
·Support output preview or video output;the video output supports different resolutions. |
| Power | ||
| 14 | AC100-240V | Port for power input;100-240V;50/60Hz;with built-in fuse. |
*The illustration is for reference only.Since the appearance of equipment may vary due to different production process,please refer to the actual product.
*The schematic of RJ11(6P6C)to DB9 cable is shown as follows:
Signal Format
|
3G-SDI |
|||||
| Input | Color
space |
Sampl
ing |
Color depth | Max.resolution | Frame rate |
|
3G |
YCbCr | 4:2:2 | 8/10bit | 1920×1080@60Hz | 50,59,94,60 |
| YCbCr | 4:2:2 | 8/10bit | 1280×720@60Hz |
23.98,24,25,29.97,30,50,59.94,60 |
|
|
HD |
YCbCr | 4:2:2 | 8/10bit | 1920×1080@60Hz | 50,59,94,60 |
| YCbCr | 4:2:2 | 8/10bit | 1280×720@60Hz |
23.98,24,25,29.97,30,50,59.94,60 |
|
| SD | YCbCr | 4:2:2 | 8/10bt | 720×576@60Hz | 50 |
| YCbCr | 4:2:2 | 8/10bit | 720×480@60Hz | 59.94 | |
| HDMI2.0 | |||||
| Input | Color
space |
Sampl
ing |
Color
depth |
Max.resolution | Frame rate |
|
4K |
YCbCr | 4:2:2 | 8/10bit | 4096×2160@60Hz |
23.98,30,50,59.94,60 |
| YCbCr/RGB | 4:4:4 | 8bit | 4096×2160@60Hz | ||
| YCbCr/RGB | 4:4:4 | 10bit | 4096×2160@30Hz | ||
|
2K |
YCbCr | 4:2:2 | 8/10bit | 1920×1200@60Hz |
23.97,24,30,50,59,94,60,100,120,144 |
| YCbCr/RGB | 4:4:4 | 8bit | 1920×1200@60Hz | ||
| YCbCr/RGB | 4:4:4 | 10bit | 1920×1200@30Hz | ||
| HD | YCbCr | 4:2:2 | 8/10bit | 1280×1200@60Hz |
23.97,24,30,50,59,94,60,100,120,144,240 |
| YCbCr/RGB | 4:4:4 | 8/10bit | 1280×1200@30Hz | ||
| HDMI1.4 | |||||
|
Input |
Color
space |
Sampl
ing |
Color
depth |
Max.resolution | Frame rate |
|
4K |
YCbCr | 4:2:2 | 8bit | 4096×1080@60Hz |
23.98,24,25,29.97,30,50,59.94,60 |
| YCbCr/RGB | 4:4:4 | 8bit | |||
|
2K |
YCbCr | 4:2:2 | 8bit | 1920×1200@60Hz |
23.97,24,30,50,59,94,60 |
| YCbCr/RGB | 4:4:4 | 8bit | 1920×1200@60Hz | ||
|
HD |
YCbCr | 4:2:2 | 8bit | 1280×1200@60Hz | 23.97,24,30,50,59,94,60,1 00,120,144,240 |
| YCbCr/RGB | 4:4:4 | 8bit | 1280×1200@60Hz | ||
| DVI | |||||
| Input | Color
Space |
Sampl
ing |
Color
depth |
Max.resolution | Frame rate |
| 4K | RGB | 4:4:4 | 8bit | 4096×1080@60Hz |
23.98,24,25,29.97,30,50,59.94,60 |
| 2K | RGB | 4:4:4 | 8bit | 1920×1200@60Hz | 23.98,24,25,29.97,30,50,59.94,60 |
| HD | RGB | 4:4:4 | 8bit | 1280×1200@60Hz | 23.97,24,30,50,59,94,60100,120,144,240 |
| Only part of the regular resolutions are listed above. | |||||
Parameters
| Dimensions (W×H×D) | |
| Device | 482.6mm(19.0")×44.0mm(1.7")×418.7mm(16.5"),1U,without foot pads |
| Packing | 550.0mm(21.7")×115.0mm(4.5")×490mm(19.3") |
| Weight | |
| Net | 4.8kg(10.58lbs) |
| Electrical parameters | |
| Power supply | AC100-240,50/60Hz |
| Rated power | 75W |
| Operating environment | |
| Temperature | -20℃~50℃ (-4F~122F |
| Humidity | 0%RH-90%RH,non-condensing |
| Storage environment | |
| Temperature | -30℃~80℃(-22°F~176°F) |
| Humidity | 0%RH-90%RH,non-condensing |
Applications
Video Processor Mode
Bypass Mode
Fiber optic transceiver mode
Reference Dimensions
